2018-12-11

recall settings on HP power suuplies (hit "Recall" button twice)

cd /home/maps/new-alpide-software/build

power on VME crate

ping -b 192.168.168.255

./stopclk

turn on ALPIDE power: 27 mA

single chip: DEVICE CHIPMOSAIC, set correct CHIPID (default is 0)

stave: DEVICE IBHIC, set appropriate ENABLED_N

./test_fifo should end with:

FIFO scan: region 31
Test finished: error counters: 
  pattern 0x0:      0
  pattern 0x555555: 0
  pattern 0xffffff: 0
(total number of tested memories: 32 * 128 = 4096)

Total error count (all chips): 0

1 chips were enabled for scan.

and ALPIDE current now ~84 mA

./test_digitalscan should end with:

Mask stage 2
Trigger train 0

Total number of 8b10b decoder errors: 0
Number of corrupt events:             0
Number of skipped points:             0
Priority encoder errors:              0

1 chips were enabled for scan.

ichip = 0 with chipId = 0
Writing data to file Data/DigitalScan_181211_161849.dat

scan settings in Config.cfg: NMASKSTAGES is number of rows, PIXPERREGION controls how many pixels/row are pulsed, NINJ is number of pulses

ALPIDE current should be ~114 mA once the high-speed data transmission is active

make a TH2: .x analysis/Hitmap.C ("Data/DigitalScan_181211_162424.dat",50)
(where 50 = value of NINJ you used for the run)


./test_threshold

Mask stage 511

Total number of 8b10b decoder errors: 0
Number of corrupt events:             0
Number of skipped points:             0
Priority encoder errors:              0

1 chips were enabled for scan.

VRESETP 0
VRESETD 147
VCASP   86
VCASN   50
VPULSEH 170
VPULSEL 121
VCASN2  57
VCLIP   0
VTEMP   0
IAUX2   0
IRESET  0
IDB     29
IBIAS   64
ITHR    50

MODECONTROL  77
FROMU_CONFIG1  32
FROMU_CONFIG2  80
FROMU_PULSING1  20
FROMU_PULSING2  500
CMUDMU_CONFIG  80

VRESETP 0
VRESETD 147
VCASP   86
VCASN   50
VPULSEH 170
VPULSEL 121
VCASN2  57
VCLIP   0
VTEMP   0
IAUX2   0
IRESET  0
IDB     29
IBIAS   64
ITHR    50

MODECONTROL  77
FROMU_CONFIG1  32
FROMU_CONFIG2  80
FROMU_PULSING1  20
FROMU_PULSING2  500
CMUDMU_CONFIG  80


.x analysis/FitThresholds.C+ ("Data/ThresholdScan_181211_162731.dat")

.x analysis/ThresholdMap.C ("Data/FitValues_181211_162731.dat")

====
power board:

./MosaicSrc/powerboard/GUI/pbGUI

initial setup:
File->Configure, enter MOSAIC address (192.168.168.248)
enter values in Vset boxes that give you correct voltage readbacks (green numbers)
File->Save to save settings to a .cfg file

restore setup (each time you start pbGUI): File->Open build/PB.cfg


now the power-up sequence is: ./stopclk, turn on analog, turn on digital

====
GUI

get on visitor network
kinit alicelanl@CERN.CH (Gudu-Difa)
./GUI/GUI