-------------------------------------------------------------------------------------------------------------------------
Reference
-------------------------------------------------------------------------------------------------------------------------
id2: Output ON, readbacks 1.799018 V 0.193578 A, OVP OK OCP OK
id3: Output ON, readbacks 1.799018 V 0.190579 A, OVP OK OCP OK
id1: Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

-------------------------------------------------------------------------------------------------------------------------
System power on:
-------------------------------------------------------------------------------------------------------------------------
1)Turn on RU fan (top most terminal)
./e363xa_on.py /dev/ttyUSB_id7
Output ON, readbacks 12.01289 V 2.777201 A, OVP OK OCP OK

2)Turn on RU second )terminal below the fan)
./e363xa_on.py /dev/ttyUSB_id1
Output ON, readbacks 4.998905 V 1.345789 A, OVP OK OCP OK

3)program RU using Vivado (Vivado is open on the right hand side
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

4)once the proram is complete initlize GBT link using python script
../../modules/board_support_software/software/py/initGBTx_v1.py ../../modules/gbt/software/GBTx_configs/GBTx0_Config.xml
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

5)Reprogram RU using Vivado
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

6)Initialize readout unit
./testbench_JS_AT_SU_nopulse.py initialize_boards
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

7)Turn on ALPIDE power supplies
./e363xa_on.py /dev/ttyUSB_id2
./e363xa_on.py /dev/ttyUSB_id3
Aproximate current draw
id2: Output ON, readbacks 1.799018 V 0.059578 A, OVP OK OCP OK
id3: Output ON, readbacks 1.799018 V 0.053579 A, OVP OK OCP OK

8)Initialize/configure sensors Readout Unit gt interface
./testbench_JS_AT_SU_nopulse.py setup_sensors
./testbench_JS_AT_SU_nopulse.py setup_readout
id2: Output ON, readbacks 1.799018 V 0.193578 A, OVP OK OCP OK
id3: Output ON, readbacks 1.799018 V 0.190579 A, OVP OK OCP OK
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

9) Configure RU arbiter
../../modules/board_support_software/software/py/wrreg.py 8 29 0xF
Output ON, readbacks 4.998905 V 1.945789 A, OVP OK OCP OK

-------------------------------------------------------------------------------------------------------------------------
Reconfigure ALPIDEs:
-------------------------------------------------------------------------------------------------------------------------
1) Power down ALPIDEs
./e363xa_off.py /dev/ttyUSB_id2
./e363xa_off.py /dev/ttyUSB_id3

2)Disable clock from ALPIDE
./testbench_JS_AT_SU_nopulse.py disable_clock
id2: Output ON, readbacks 1.799018 V 0.059578 A, OVP OK OCP OK
id3: Output ON, readbacks 1.799018 V 0.053579 A, OVP OK OCP OK

3)Initialize/configure sensors Readout Unit gt interface
./testbench_JS_AT_SU_nopulse.py setup_sensors
./testbench_JS_AT_SU_nopulse.py setup_readout
id2: Output ON, readbacks 1.799018 V 0.193578 A, OVP OK OCP OK
id3: Output ON, readbacks 1.799018 V 0.190579 A, OVP OK OCP OK

-------------------------------------------------------------------------------------------------------------------------
Periodically run
-------------------------------------------------------------------------------------------------------------------------
./testbench_JS_AT_SU_nopulse.py refresh_pixels
-------------------------------------------------------------------------------------------------------------------------
                                                                                                              49,1          41%